Procyon-Extreme Pre-Spray

$26.11 Gallon

1. Dirt and grease gets ground into the carpet.
Procyon Extreme gets deep down into the carpet to break up and dissolve all the grime and dirt. Then the sodium in Procyon Extreme pushes all the dirt and grime to the top for easy and successful extraction.
2. Heavily soiled carpet with lots of foot traffic lays over and becomes flat.
Procyon Extreme has a water softening agent that rejuvenates the carpet fibers. The carpet comes back to life feeling soft and looking full like it’s brand new.
3. Procyon Extreme works in only 1 or 2 Steps!
When you see a heavily soiled entry way you start to gear up and think ‘I might need to do three or four steps to get all this out’. But this method costs more time and more money on products. Procyon Extreme will cut that in half by doing only two steps.
1 Step: Pre-spray and let dwell for 10 to 15 minutes, agitate and then do a fresh hot water extraction.
If you feel it needs a little more….
2 Step: Pre-spray with Procyon Extreme and let dwell for 10 to 15 minutes agitate and also rinse with Procyon Extreme and then agitate extract with fresh hot water.
Directions
TEST FOR COLOR FASTNESS: Prior to cleaning, test an out of the way area of carpet to insure color fastness. Apply a small amount of mixed, ready-to-use PROCYON to the area, wait one minute and blot with a white cotton towel (BLEACH FREE). Check for color fastness. User assumes all liability and risk. Using more is NOT better. Use as directed. Improper dilution and use can have increased risk of health effects. NOTE: THE HOTTER THE WATER THE MORE EFFECTIVE THE CLEANING. Product does not expire.

DIRECTIONS: SHAKE BEFORE USING. Vacuum thoroughly. For home use, follow directions for portable extraction.

PRE-SPRAY/EXTRACTION: For use on heavily soiled carpet traffic areas. Effectively dissolves grease, dirt, grime, spots and stains. Mix 4 oz. to 1 gallon of COLD, WARM, or HOT water. Pre-spray evenly. DO NOT OVER WET. Let dwell for 10 minutes. Extract with fresh water.

PORTABLE EXTRACTION (without pre-spray): Mix 4 oz. to 1 gallon of COLD, WARM, or HOT water. For all portable extractors including extractors with a siphon tube. In this case, simply place the siphon tube into the concentrated liquid.

ENCAPSULATION PRE-SPRAY: Mix 4 oz. to 1 gallon of COLD, WARM or HOT water – agitate. After fiber dries, vacuum thoroughly.

BONNET CLEANING: Mix 4 oz. to 1 gallon of COLD, WARM, or HOT water. Pre-spray evenly on heavily soiled area. Let dwell for 10 minutes. For best results, bonnet using 100% cotton bonnet pads.

WICKING & BROWNING: Mix 2 oz. to 1 gallon of COLD, WARM or HOT water. Pre-spray the carpet fiber. DO NOT OVER WET. Let dwell for 10 minutes. For best results bonnet using 100% cotton bonnet pads to absorb moisture and to prevent wicking or browning problems.

UPHOLSTERY: Mix 2 oz. to 1 gallon of COLD or WARM water. Pre-spray evenly, applying from the base of the upholstery going up and extract from the top going down.

HYDRO FORCE: Mix 32 oz. to 1 gallon WARM or HOT water (meter 1:8). Apply evenly. Let dwell for 10 minutes.

TRUCK MOUNT: Fresh water rinse. Set heat at 180° to 200° F. NOTE: Rinsing agents are not needed.

Out of stock

Categories: ,

Product Description

1. Dirt and grease gets ground into the carpet. Procyon Extreme gets deep down into the carpet to break up and dissolve all the grime and dirt. Then the sodium in Procyon Extreme pushes all the dirt and grime to the top for easy and successful extraction. 2. Heavily soiled carpet with lots of foot traffic lays over and becomes flat. Procyon Extreme has a water softening agent that rejuvenates the carpet fibers. The carpet comes back to life feeling soft and looking full like it’s brand new. 3. Procyon Extreme works in only 1 or 2 Steps! When you see a heavily soiled entry way you start to gear up and think ‘I might need to do three or four steps to get all this out’. But this method costs more time and more money on products. Procyon Extreme will cut that in half by doing only two steps. 1 Step: Pre-spray and let dwell for 10 to 15 minutes, agitate and then do a fresh hot water extraction. If you feel it needs a little more…. 2 Step: Pre-spray with Procyon Extreme and let dwell for 10 to 15 minutes agitate and also rinse with Procyon Extreme and then agitate extract with fresh hot water. Directions TEST FOR COLOR FASTNESS: Prior to cleaning, test an out of the way area of carpet to insure color fastness. Apply a small amount of mixed, ready-to-use PROCYON to the area, wait one minute and blot with a white cotton towel (BLEACH FREE). Check for color fastness. User assumes all liability and risk. Using more is NOT better. Use as directed. Improper dilution and use can have increased risk of health effects. NOTE: THE HOTTER THE WATER THE MORE EFFECTIVE THE CLEANING. Product does not expire. DIRECTIONS: SHAKE BEFORE USING. Vacuum thoroughly. For home use, follow directions for portable extraction. PRE-SPRAY/EXTRACTION: For use on heavily soiled carpet traffic areas. Effectively dissolves grease, dirt, grime, spots and stains. Mix 4 oz. to 1 gallon of COLD, WARM, or HOT water. Pre-spray evenly. DO NOT OVER WET. Let dwell for 10 minutes. Extract with fresh water. PORTABLE EXTRACTION (without pre-spray): Mix 4 oz. to 1 gallon of COLD, WARM, or HOT water. For all portable extractors including extractors with a siphon tube. In this case, simply place the siphon tube into the concentrated liquid. ENCAPSULATION PRE-SPRAY: Mix 4 oz. to 1 gallon of COLD, WARM or HOT water – agitate. After fiber dries, vacuum thoroughly. BONNET CLEANING: Mix 4 oz. to 1 gallon of COLD, WARM, or HOT water. Pre-spray evenly on heavily soiled area. Let dwell for 10 minutes. For best results, bonnet using 100% cotton bonnet pads. WICKING & BROWNING: Mix 2 oz. to 1 gallon of COLD, WARM or HOT water. Pre-spray the carpet fiber. DO NOT OVER WET. Let dwell for 10 minutes. For best results bonnet using 100% cotton bonnet pads to absorb moisture and to prevent wicking or browning problems. UPHOLSTERY: Mix 2 oz. to 1 gallon of COLD or WARM water. Pre-spray evenly, applying from the base of the upholstery going up and extract from the top going down. HYDRO FORCE: Mix 32 oz. to 1 gallon WARM or HOT water (meter 1:8). Apply evenly. Let dwell for 10 minutes. TRUCK MOUNT: Fresh water rinse. Set heat at 180° to 200° F. NOTE: Rinsing agents are not needed.